Special Offer
-
Display screens, Raspberry Pi
7inch touch LCD Screen multi function
QUICK OVERVIEW
- Touch Panel with HDMI + USB Cable for Raspberry Pi
- for protecting screen, Please use our free matched HDMI & power cable
- To avoid not viewing full screen, Please adjust the resolution by yourself on First using.
- Support Raspbian,Ubuntu,Kodi,win10,IOT.
- for computer screen, support win7,win8,win10 system 5 point
- touch(Xpor older system single point touch).
SKU: RA214 -
-
Motors & Drivers
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
QUICK OVERVIEW
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Coolant enable
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
SKU: AA153 -
-
Arduino
Arduino UNO R3 Acrylic Case
QUICK OVERVIEW
- For Arduino UNO R3 Development Board only.
- With screw copper pillar and installation instructions.
- To protect your little computer against damages, dust and scratches Clear Top and Bottom.
- This case provides easy access to all ports.
- It requires no tools for easy assembly and disassembly.
- Simply Clicks Together Enclosure.
SKU: AC011
-
-
Arduino
Arduino UNO R3 Acrylic Case
QUICK OVERVIEW
- For Arduino UNO R3 Development Board only.
- With screw copper pillar and installation instructions.
- To protect your little computer against damages, dust and scratches Clear Top and Bottom.
- This case provides easy access to all ports.
- It requires no tools for easy assembly and disassembly.
- Simply Clicks Together Enclosure.
SKU: AC011 -
Arduino
Arduino Nano CH340 Chip Board
QUICK OVERVIEW
- Operating Voltage (logic level): 5V
- With Soldered Connector
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
SKU: AA007
Products Grid
Best Sellers
Recently Added
Motors & Drivers
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
QUICK OVERVIEW
Latest Arduino CNC Shield Version 3.10
GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
Coolant enable
Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
Compact design.
4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
SKU: AA153
Arduino
Arduino UNO R3 Acrylic Case
QUICK OVERVIEW
For Arduino UNO R3 Development Board only.
With screw copper pillar and installation instructions.
To protect your little computer against damages, dust and scratches Clear Top and Bottom.
This case provides easy access to all ports.
It requires no tools for easy assembly and disassembly.
Simply Clicks Together Enclosure.
SKU: AC011
Arduino
Arduino Nano CH340 Chip Board
QUICK OVERVIEW
Operating Voltage (logic level): 5V
With Soldered Connector
8 analog inputs ports: A0 ~ A7
14 Digital input / output ports: TX, RX, D2 ~ D13
1 pair of TTL level serial transceiver ports RX / TX
Using Atmel Atmega328P-AU MCU
There is a bootloader installed in it
Standard 0.1” spacing DIP (breadboard friendly).
Manual reset switch.
SKU: AA007
Arduino
Ethernet W5100 Shield Network Expansion Board for Arduino
QUICK OVERVIEW
Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
Stackable Design, can directly be supported by for Arduino official Ethernet Library.
Supports up to four simultaneous socket connections
Can be used to store files for serving over the network.
Can be accessed using the Mini SD TF library.
IEEE802.3af compliant
Low output ripple and noise (100mVpp)
Overload and short-circuit protection
SKU: AA009
Motors & Drivers
L293D Motor Driver/Servo Shield for Arduino
QUICK OVERVIEW
2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
Can run motors on 4.5VDC to 25VDC.
Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
SKU: AA031
Arduino
DS1302 RTC Real Time Clock Module with Battery
QUICK OVERVIEW
The DS1302 trickle-charge timekeeping chip module with battery backup contains a real-time clock/calendar and 31 bytes of static RAM. It communicates with a microprocessor via a simple serial interface. The real-time clock/calendar provides seconds,minutes, hours, day, date, month, and year information.
SKU: AA122
Motors & Drivers
Servo MG996 13KG 180 degree
QUICK OVERVIEW
Weight: 55g
Dimension: 40.7×19.7×42.9mm
Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v)
Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v)
Operating voltage: 4.8 ~ 6.6V
Gear Type: Metal gear
Dead band width: 1us
Wire length: 32cm
SKU: AA023
Motors & Drivers
Servo MG996 13KG 360 degree
QUICK OVERVIEW
Weight: 55g
Dimension: 40.7×19.7×42.9mm
Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v)
Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v)
Operating voltage: 4.8 ~ 6.6V
Gear Type: Metal gear
Dead band width: 1us
Wire length: 32cm
SKU: AA229
Relays & Contactors
5V Dual Channel Relay Module
QUICK OVERVIEW
Low Level Trigger Relay Module
Two separate LEDs for On/Off indication of the Relay.
Triggering input voltage 3.3V – 5V
Two separate LEDs for On/Off indication of the Relay
Triggering input voltage 3.3V – 5V 4)
Back EMF protection
Back EMF protection 2 LEDs to indicate when relays are ON.
Works with logic level signals from 3.3V or 5V devices
Opto isolation circuitry
Module with diode current protection, short response time
AC Control Voltage: 250V @max.10A
DC Control Voltage: 30V @max. 10A
SKU: AA025